Cat flaps allow your pet to leave and come at their own pace without you having to let him in or out. They also help prevent your cat from toileting in the house.

It is easier to install a cat flap on a upvc panel than one made of glass but you'll require some expertise and right tools.

Take a measurement of the door

The installation of a cat flap in a front door could be difficult however, provided that the cat flap is the right type and you follow the guidelines you can make it less difficult. We will show how to trace the shape, fitting Cat flap in upvc door Panel using a jigsaw to cut out the door's area and then finish off the job by fixing the flap to the door. This will ensure the flap remains in place and shields the doors from damage caused by rain and wind.

To determine the size of the cat flap that you need, measure the width of your pet. This will enable you to select a cat flap that is large enough to allow your pet to walk into the house and exit without having to open the door every time.

If your kit has an illustration of where to drill then you can put it on the door and then draw around it. If your door has sill or moulding along the bottom of it ensure you have clearance from these because this will keep your cat safe and prevent them gaining access to your home.

Set a square to check that you're cutting correctly and ensure that the hole is a perfect rectangle shape. Once you are satisfied with the result, you can start removing the rest of the door material. If you own an already-cut square, make use of it to verify whether you're cutting in the right way and to make sure the hole is a good rectangle. Once you are happy with this you can start to remove the rest of the door material.

Draw a Line

The cat flap installation cost flap is a great way to allow your pet to go out and in without worrying about them being a nuisance to guests or leaving unwelcome gifts in the home. It also stops draughts and helps keep the temperature inside your home steady. However, fitting a cat flap the cat flap to your door might seem like an overwhelming task for those who have never done it before, which is why many to hire a professional carpenter or joiner to do the job. While this is certainly an option, it is possible to complete the task yourself if you own the right tools and follow the instructions carefully.

This is much simpler to do with a wooden door, but it is possible with uPVC. However it is important to be cautious not to harm the doors because this will cause the door to be damaged and invalidate your warranty. The first step is to take measurements of the door to ensure that it can accommodate the new cat-flap. If you have an ordinary uPVC panel it should be a breeze. However in the case of made of composite or another kind of door, you may require more care.

The next step is to measure the height of your cat's stomach. This is the measurement from the floor to the underside of the cat's stomach, and you'll need to find a spot in the door that will be within the range that your cat is able to comfortably walk through. Once you've got the information you'll have to mark the area with a spirit level and a pencil so you are certain that the hole will fit your cat.

Once you've marked the area, you're now ready to cut the hole. You will need to use a jigsaw and it is essential to take your time to ensure that the cuts are smooth and straight, fitting cat flap in upvc door panel rather than uneven and rough, since this could damage your door. Be sure to wear safety glasses and a dust-proof mask at all times when working with the jigsaw as inhaling the sawdust could be hazardous to your health. Once you have completed the cutting, you'll need to smooth out the edges of the hole using sandpaper, so that your cat flap will fit easily into place.

Cut a hole

It can be difficult to install an animal flap on the door panel or double glazing unit. If you are not very proficient in DIY, it's best to employ a professional to complete the work for you. A mistake could not only look ugly but also pose a security threat. It could let cold air in when the cat is outside and hot air out when the cat is inside.

Mark the hole's position on the door with the help of a pencil and a spirit level. This will ensure it is correctly positioned and is flush with the rest of the door. You should make sure you have an sandpaper piece on the ready for any rough edges.

Wear the safety equipment you'll need to use an electric tool. If you're concerned about the noise, you can buy an electric jigsaw that is quieter and easier.

It is best to only remove the material required to make the cat flap. A little bit of extra material is required to increase the thickness of the wall of the cat flap itself but removing more than that can cause problems and even damage the doors frame.

If the upvc door features a metal panel or frame, it could interfere with the microchip flap. In this case you'll need make an oversize hole to ensure that the metal doesn't touch the wall of the flap.

If you're planning to install the cat flap onto the frame of a double glazed window with cat flap with a metal frame then you'll need to speak to a professional who can provide you with a new glass pane with the hole for the cat flap premade inside. It will be much cheaper to have this done instead of trying to install the flap to an existing pane of glass that has not been manufactured specifically for the purpose.

Fit the Flap

Cat flaps allow your pet to move around as they please, giving them the freedom to lounge in the home whenever they want to. If you have a uPVC front door, it may be hard to install a cat flap. This is particularly true if you do not own glass panels that is cut. If you're willing to install a half-glazed uPVC replacement panel, it's possible to install an additional cat flap. It's not as simple as just cutting a hole in the door however, and there are a few things you'll need first to ensure that it's secure.

A composite, uPVC, or GRP door panel is generally made up of a plastic skin which is bonded to an insulating polystyrene base. It is crucial to be careful when cutting the material. This type of door has a template can be used to cut the hole.

After you've marked the location of the hole in your door, it's now time to put in the cat flap fitters flap itself. You can pick from a range of options, from simple push-button units to microchip-activated ones that allow only your pet to enter. But, regardless of the type of cat flap you pick, it's important to make sure that your cat can comfortably use the flap without becoming trapped in the weather.

A circular fitting cat Flap in upvc door Panel is superior than a square because circles can be cut more securely into the glass. This is because square holes make the glass more susceptible to cracking if drilling is applied to it. It's also a safer choice to use since you don't risk having to drill into toughened glass that might break and hurt your pet or your family. This is especially crucial if you have a child or elderly person in your home who could be hurt by shards of glass.