Replacement UPVC Door Handles

If you're replacing your handles or adding a little more security, you can choose the perfect handle for your Composite door handle replacement. These upvc handles are easy to fit and comply with the required 92mm centres of multipoint locks.

The most important measurements to consider are backplate fixing centres and key hole dimensions and levers. Compare these measurements carefully with your existing measurements prior to placing an order.

Lever/Pad

Lever pad handles for doors consist of an elongated lever handle on one side and a paddle shaped handle on the other. These are designed to be used with key wind locks, however, they can also be fitted to multipoint split spindle door locks (though you'll require an additional dual spindle lock case).

Our range of upvc handle lever pads are available in a wide range of finishes. They will be displayed in the drop down list after you have identified the correct handle for your door. Some styles of handles are not available in all finishes. You should always examine the technical drawing and dimensions for the item you are looking to ensure that you receive the right fit and size.

When selecting the new set of upvc lever pad door handles it is crucial to make sure that they match the PZ (distance between the handle spindle and the center of the hole for the cylinder) of your existing multipoint door locks, since they have to be in line to ensure that the doors remain locked, either from the inside or outside. The handles we offer are designed to work with the majority of standard cylinder locks, however it is advisable to double-check before purchasing.

If you want to upgrade to dual spindle levers you'll need to take out the handles you have already installed and disassemble the lock case. This will require an extra split cylinder inline. These are available separately, and we provide a full technical diagram to take a look at in the pictures for each product.

After you have removed the screws that are holding the door handle you have, it is a good idea to loosen them and inspect the mechanism to see the condition it is in. It is possible that you will need to loosen the screws further when they aren't tight. After that, you can take off the old handle and spindle and replace it with a new upvc door handle. Before screwing the handle into place it is a good idea to make sure it is in the proper place. You can do this by placing your finger in the gap between the frame of the door handle lock repair and the door handle to ensure that it is level.

Lever/Lever

The lever door handles are used to operate a multi-point lock with the Euro cylinder. They can be found on a variety of double upvc doors as well as wooden and aluminum doors. They are equipped with a lever inside and an outside paddle and are typically available in two different types. Sprung - These have a spring cassette installed within the backplate that helps bring the handle lever to a horizontal position. Non-sprung: These do NOT include a mechanism that can spring the handle lever to a horizontal angle.

To fix a sagging door handle lever you'll need to locate the hole or pin that is the detent access point. It's usually a small hole or protruding ring, or rectangle, that is located on the base of the handle plate. Once you have located the hole for accessing the detent or pin, you can remove it using a screwdriver.

Once the handle is positioned horizontally, you can put back the screws. Tighten them to ensure that the handle is securely connected to the base plate. You may want to apply a threadlocking solution to the screw threads in order to increase grip and prevent them from loosing over time.

Drooping lever door handles repair near me handles could be the result of many factors. The most common cause is that the fixings aren't tight and the lever bearing to get tangled against the door handles repair near me. It could also be due to the fact that the levers are not being operated at a straight angle and this is causing compression of the latch mechanism and preventing it from fully springing back into service.

Another common reason is that the sprung lever isn't operating correctly and this is typically due to the spring not being in the right position within the backplate. To check if the handle returns to horizontal, simply move it.

It is essential to fix any door handles that are damaged immediately. This can cause excessive wear on the screws and the handle could fall off the base plate. You should also tighten any loose screws on a regular basis to prevent them from becoming looser.

Lever/Snib

The handles for doors made of upvc are also known as 'Snib' handle sets and have a snib button at the top of the lever that you can push down to lock your door in the event that you don't have a dummy lock. These door handles are fitted with a Fullex lock 68PZ. (68mm between the spindle and the centre of the lock). We also stock a range of door handles 68PZ from manufacturers such as Ferco and Fab & Fix.

You can update your home by changing the door handles whether you are replacing your existing handles or installing new ones on doors that you've built. There are various styles available for upvc door handles, including the traditional levers on backplates. Other options include straight or curly short latches, and Dummy knobs for multi-point locks. These are great for French doors.

Rose door handles are oval or circular versions of backplate lever handles. These kinds of door handles come with the knob or lever on a backplate which is placed behind the lever or knob and is sometimes called the rosette, however certain back plates can be removed to be concealed for fixing.

The handles are available in a variety of finishes including chrome and coloured finishes, to match your door and other hardware like knobs, bolts and hinges. Some handles come with grub screws to help firmly attach the knob or lever to the spindle. Some handles are equipped with bathroom spindles which are suitable for bathroom locks. They also come with a thumbturn release mechanism, and can be used on bathroom doors.

Mortise

If your uPVC front door handle is stuck in the open position, the cause will most likely be with the tubular latch. It could be due to various reasons, but the most common is an absence of lubrication within the latch plate. This can be corrected easily by simply opening the door and Door lock Handle repair spraying lubricant onto the lock and handle. It could also be that the latch is loose from the backplate. This could be more of a problem and will require a specialist to repair door handle.

A multipoint handle system is the best solution for stuck door handles. These handles mount through the door's faceplate and are operated with the thumb turn knob or key which activates a cam that locks the deadbolt. The handles are available in a variety of sizes to suit different types of upvc door handle repair doors. They also come with a variety of attractive finishes to match existing hardware. These handles can be purchased via the internet or from an authorized locksmith in your area. They can be installed with clear instructions.

To choose a replacement handle set, you will be required to know the PZ size of your cylinder. This is the distance from the edge of the frame of the door to the central edge of the hole in the handle in millimetres. You will also need to know if your door has hook locks or a mortise style lock. Once you know these measurements, the simplest method to determine the right handles is to filter by brand on the website. This will narrow down your options, and you will then select the correct size from the list.

A typical handle set includes the handle unit and a pair of different length screws as well as drill guides and installation instructions. The smart versions, such as the Igloohome Smart Mortise 2+ comes with a complete mortice lock with an integrated keypad. These are more sophisticated devices and are best suited to professional installers or skilled DIYers. Some handle sets have a range of additional accessories, such as weather strips, that can be used to improve the look of the door.